![]() 187 Label Cue – Change the label of the current cue.186 Set Cue Time – Change the overall time of the current cue.184 Knock out – Remove selected fixture from the Programmer.183 Hurry Cue – Play into current cue in 1 second (used if you goto a cue and it has a long fade time you want to override for editing).172 Snapshot – Store a cue using the Look store selection.168 Video OFF – Knockout active Video values of the selected fixture from the Programmer.167 Shapers OFF – Knockout active Shapers values of the selected fixture from the Programmer.166 Control OFF – Knockout active Control values of the selected fixture from the Programmer.165 Focus OFF – Knockout active Focus values of the selected fixture from the Programmer.164 Beam OFF – Knockout active Beam values of the selected fixture from the Programmer.163 Color OFF – Knockout active Color values of the selected fixture from the Programmer.162 Gobo OFF – Knockout active Gobo values of the selected fixture from the Programmer.161 Position OFF – Knockout active Position values of the selected fixture from the Programmer.160 Dimmer OFF – Knockout active Dimmer values of the selected fixture from the Programmer.159 Dimmer Check Setup – Places selected fixtures in Preset 0.919.Then select all of your fixtures and put them in Preset 0.919, then use Macro 158 to advance one by one through the rig to do a quick system test. Then create a Preset 0.920 that has your fixtures at full in their default/open state. 158 Dimmer Check – To use this in its intended mode: Create a Preset 0.919 that has all functions of fixtures in (Pan/Tilt at full, douser in, gobos rotating, color black, etc).154 Disable MSC Out – Disable input of MIDI Show Control. ![]() 153 Disable MSC In – Enable input of MIDI Show Control.152 Source LTC – Change the source of a timecode pool item to SMPTE (LTC).151 Source MIDI – Change the source of a timecode pool item to MIDI.135 Color Chase Generator – Same as Macro 134 but is hard set to Presettype Color.You’ll also enter the Presettype that you want. Macro asks for number of steps and which Presets to use. 134 Chase Generator – Creates a 2 to 5 step Chase Sequence on the selected Executor using the selected fixtures.You’ll need to know the number of the form you want to edit before starting the Macro. 132 Edit Form Color Effect – Used to refine the color values for a form already created using Macro 131.When you import the effect, the form will automatically import as well. PSR will mess up the forms and lose their labeling. When you go to a new show and want to bring over these effects, use import and not PSR. Finally it asks you for the number of steps and the values for each color. The macro asks you for an open slot to create a form and an effect. The Form is where your RGB values are stored and work together with the effect. This creates two things: An Effect and a Form. You need to know the raw percentage values of RGB for each color you are going to create (Simulates an absolute effect on the Eos). 131 Form Color Effect – This creates a 2 to 6 step color effect using the effect engine.101 Odd – Select odd fixtures in Programmer.102 Even – Select even fixtures in Programmer.103 Invert – Invert the selection of fixtures in the Programmer.104 Shuffle Selection – Shuffle the order of the fixtures in the Programmer.105 Reverse Delay – Apply the delay ranges set from Macro 107 in the reverse order.106 Repeat Delay – Apply the delay ranges set from Macro 107.107 Delay Offset – Enter a delay time range to apply to all parameters of selected fixtures in the programmer.108 Smart Delay – Operates same as Macro 107 but with entry for a different delay range for just Color.109 Trackball Normal (Course/Fine) – After using Macro 301 to enter what user number you are, can change the resolution of the trackball.110 Delay FCB – Enter a delay time to apply to all parameters except Intensity for all fixtures in the Programmer.111 Flip – Flip the pan and tilt of a moving light.112 Delay Set – Apply delay to all parameters of all selected fixtures.113 Individual Time Set – Apply fade to all parameters of all selected fixtures.116 Set Cue To Basic Time – Remove all individual fade and delay times from the current cue.117 Sel At Basic Time – Remove individual timing for fixtures selected.
0 Comments
Leave a Reply. |